Our electric smoke extractor has a 6-speed regulator, so you only need to set it to speeds of 1-2 to help extract smoke naturally, but not heat. Basically, at the first two speeds, we are not altering in any way the normal operation of a fireplace, which would normally disperse a very small amount of heat in the smoke rising in the flue pipe. The Gemi chimney fan sucks up the smoke that would otherwise go into the house and therefore, certainly, would not produce any heat sources for the indoor environment. It is clear that if the chimney fan does not operate at the sixth speed (usually at this speed it is used to change the air in rooms, to help start fires or to suck up the ashes), with its 2500m³/h(basic) - 3800m³/h(pro) it will be so powerful that it will also suck up the heat, because it will increase the speed of combustion of the wood and consequently partially reduce the heat. Scientific studies have shown that the Gemi smoke extractor can control heat loss, so it is advisable to use a chimney to prevent heat loss. This can be seen in the millions of satisfied customers all over the world since 1983, when the first Gemi chimney fan was created.

The base of the electric chimney fan is standard 43x43 cm, the height is 35 cm, without the brackets. Considering the brackets it is 50 cm. For more specific measurements, a diagram showing the measurements of each individual part of the electric fireplace extractor fan is available on our website.

The function of the smoke extractor is to regulate the draught of the chimney, in order to solve the problem of smoke in the chimney, oven, stove, barbecue and to reproduce the natural draught of the chimney.

The assembly of the chimney smoke extractor is do-it-yourself. Watch the tutorial video on the product sheets to assembly the chimney fan. If you encounter problems with the installation of the extractor fan, you can ask for the help of an electrician or a bricklayer. If you have any doubts about the installation of the product (e.g. connection of wires, speed regulator, etc.) our specialist technicians will be at your disposal via email, chat or telephone.

If you have a square chimney with a pipe of the same height as the masonry, you must first close the gap between the pipe and the masonry and then install the chimney fan directly on the masonry. Similarly, if the pipe is only a few centimeters (or inches) high, the pipe must be brought to the same height as the masonry. In this situation you have to buy the model of chimney fan with square base, adjustable also for rectangular chimney.

It is possible, but you have to consider the dimensions of the chimney fan. The installation of the smoke exhauster can be done in two ways: eliminating the cap of the chimney and then installing the chimney fan, or inserting inside the chimney the chimney smoke extractor, ordering in this case the smoke extractor without the cap.

Yes, it is possible. There are two ways to make the electrical connection: with the 3 x 1.5 cable (to be run outside the chimney up to the speed regulator) in order to extend the first metre attached to the chimney fan. Or you can make an internal connection to the chimney with our high-temperature resistant cable, which you can purchase separately by selecting the desired quantity in the drop-down menu according to how many meters you need.

There is no time limit. The chimney smoke extractor can work all day without any problem.

The professional fan for fireplaces can be installed at any height, even on flues of 1 meter. On the other hand, the basic model of the chimney fan is recommended for chimneys over 3 m high.

No, the chimney fan does not plug the smoke outlet if it is switched off. For this reason it is possible to switch on the chimney fan only in certain situations, for example when raising the stove door or in case of strong wind.

No, the base of the chimney smoke extractor has been raised to prevent water infiltration in the event of rain.

Certainly, our chimney fan is suitable in case of strong wind because it solves the problem of smoke.

Yes, thanks to the suction power of the chimney fan there is no problem even on chimneys longer than 50 meters.

Yes, we supply adapters for round flues (those indicated in the product drop-down menu). To order the adapter, simply select the round flue and choose the size of the adapter you wish to purchase from the drop-down menu. You have to take into consideration the external diameter because our adapter for flues fits externally to its outlet. If the chimney has an external diameter of 25 cm, the ideal chimney adapter will be 25 cm in the drop-down menu.

No. The chimney fan is silent at any speed. Of course, if you set it to the sixth speed, the fan makes more than 1300 revolutions per minute, so you will hear a slight humming sound. But to solve the problem of smoke, the fan should be used at low speeds, from the first speed up to the third speed. At these speeds the sound pressure does not exceed 38 Db, i.e. zero noise.

The weight of the fan, excluding the speed regulator, is about 20 kg.

The regulator of the chimney fan for fireplaces must be connected to the 220 V current and can be installed in any area, the important thing is that it is not placed near heat sources. In fact, inside the regulator of the chimney fan there is a transformer that works at high temperatures.

There is no problem, the smoke extractor works normally. The chimney fan is designed to ensure normal running-in of the internal bearings. The fan should initially be run in at higher speeds and after a few minutes it can be switched to lower speeds. This mode of operation should only be followed for the first month, after which it will also run at lower speeds.